Cincinnati 2100 Configuration
CNC Parameters
Baud Rate: 9600
FactoryWiz DNC Settings
Basic Communication
Sending Options
2.11- Leader: Leave blank
2.12- Trailer: Leave blank
2.23- Skip lines that contain: Leave blank
2.31- Automatic timeout: 7
Receiving Options
3.11- Program identifier 1: (
3.12- Program Identifier 2:
3.21- Receive timeout: 3
3.31- Ignore data before first end-of-block: False
3.32- Ignore data after last end-of-block: False
Remote Commands
4.02- Request for file command: GET-
4.03- Request for file command (drip feed):
4:11- Request to save command:
Additional Notes
Changing CNC Parameters
To set up parameters:
Click on MORE
Click on SYSTEM CONFIGURATION
Click on CNC COM SETUP
Click on HARDWARE tab
Change parameters as needed.
Outputting CNC Programs
Click on HOME SCREEN
Click on PROGRAMS
Click on TRANSFER PROGRAM
Cursor to program that will be sent
Click on OUTPUT
Click on COM PORT
Click on START TRANSFER
Inputting CNC Programs
Click on HOME SCREEN
Click on PROGRAMS
Click on TRANSFER PROGRAM
Click on INPUT
Click on COM PORT
Click on START TRANSFER
Wiring Diagram
Pinout includes RTS/CTS Handshaking DB9 at machine
DB-9 com port | Wire color | DB-9 CNC | Jumper? | |
| (Disconnected) | Shield | 1 |
|
| 2 (Receive Data) | Green | 3 (Transmit Data) |
|
| 3 (Transmit Data) | Red | 2 (Receive Data) |
|
| 5 (Signal Ground) | Black | 5 (Signal Ground) |
|
| 7 (RTS) | Brown | 8 (CTS) |
|
| 8 (CTS) | Blue | 7 (RTS) |
|
|
|
| 6 (DSR) 1 (DCD) 4 (DTR) | JUMPER |
Pinout includes RTS/CTS Handshaking DB25 at machine
DB-9 com port | Wire color | DB-25 CNC | Jumper? | |
| (Disconnected) | Shield | 1 |
|
| 2 (Receive Data) | Green | 2 (Transmit Data) |
|
| 3 (Transmit Data) | Red | 3 (Receive Data) |
|
| 5 (Signal Ground) | Black | 7 (Signal Ground) |
|
| 7 (RTS) | Brown | 5 (CTS) |
|
| 8 (CTS) | Blue | 4 (RTS) |
|
|
|
| 6 (DSR) 8 (DCD) 20 (DTR) | JUMPER |
Related Articles
Cincinnati 850 Configuration Document
CNC Parameters Machine Parameters for Dataline: Baud Rate = 4800 Parity = NONE Data Bits = 8 Stop Bits = 1 Protocol Level = 1 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 8 1.13- ASCII None ...Cincinnati 850Sx Configuration Document
CNC Parameters Machine Parameters for Dataline: Baud Rate = 4800 Parity = NONE Data Bits = 8 Stop Bits = 1 Protocol Level = 1 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 8 1.13- ASCII None ...Cincinnati 900 Configuration Document
CNC Parameters Machine Parameters for Dataline: Marriage Parameter: 150 = 0 (NO PARITY) 151 = 10 (4800) 152 = 0 (1 stop bit) FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 7 1.13- ASCII Even ...Haas Configuration
CNC Parameters Newer Haas Press SETNG to bring up the machine settings. Press right arrow until you get to I/O tab. Press WRITE/ENTER button (lower right corner of panel). Use left and right arrow to toggle between choices for each setting. Press ...Brother C00 FTP Configuration
CNC Configuration Sheet for FTP – Brother C00 You will need to verify all parameters listed below that correspond to your CNC control. Document (Phone camera) original settings before making modifications! CNC Parameters: Press EDIT button. Press ...