Cincinnati 850Sx Configuration Document

Cincinnati 850Sx Configuration Document

CNC Parameters


Machine Parameters for Dataline:

Baud Rate = 4800

Parity = NONE

Data Bits = 8

Stop Bits = 1

Protocol Level = 1

FactoryWiz DNC Settings

Basic Communication

1.01- Port Type: Standard

1.11- Baud: 4800

1.12- Data Bits: 8

1.13- ASCII None

1.14- Stop Bits: 1

1.15- Handshake: RTS/CTS

1.16- Handshake Send Signal: CTS


Sending Options

2.11- Leader: <0>%<13><10>

2.12- Trailer: %<0>

2.23- Skip lines that contain: %

2.31- Automatic timeout: 7


Receiving Options

3.11- Program identifier 1: (PGM=

3.12- Program Identifier 2:

3.21- Receive timeout: 3

3.31- Ignore data before first end-of-block: True

3.32- Ignore data after last end-of-block: True


Remote Commands

4.02- Request for file command: GET-

4.03- Request for file command (drip feed): DNC-

4:11- Request to save command: PUT-


Additional Notes


Outputting CNC Programs:

PRGM MGMT. --> SAVE
SELECT LINE
CLICK START



Inputting CNC Programs:


TO LOAD TO MEMORY:
PRGM MGMT. --> LOAD
SELECT LINE
CLICK START

TO LOAD TO DIRECTORY:
PRGM MGMT. --> TRANSFER
FROM LINE
TO STORE
HIGHLIGHT PROGRAM TO OVERWRITE
CLICK START

TO ISSUE REMOTE REQUEST:
PRGM MGMT. --> TERMINAL
KEY IN "GET-XXXXXXXX" THEN HIT ENTER
IF YOU MAKE A MISTAKE, NO BACKSPACE
JUST HIT ENTER AND TRY AGAIN
NOW HIT THE ESCAPE KEY TO EITHER LOAD OR TRANSFER


Wiring Diagram

Pinout includes RTS/CTS Handshaking


DB-9 com port

Wire color

DB-25 CNC

Jumper?


(Disconnected)

Shield

1



2 (Receive Data)

Green

2 (Transmit Data)



3 (Transmit Data)

Red

3 (Receive Data)



5 (Signal Ground)

Black

7 (Signal Ground)



7 (RTS)

Brown

5 (CTS)



8 (CTS)

Blue

4 (RTS)





6 (DSR)

8 (DCD)

20 (DTR)

JUMPER





    • Related Articles

    • Cincinnati 850 Configuration Document

      CNC Parameters Machine Parameters for Dataline: Baud Rate = 4800 Parity = NONE Data Bits = 8 Stop Bits = 1 Protocol Level = 1 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 8 1.13- ASCII None ...
    • Cincinnati 900 Configuration Document

      CNC Parameters Machine Parameters for Dataline: Marriage Parameter: 150 = 0 (NO PARITY) 151 = 10 (4800) 152 = 0 (1 stop bit) FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 7 1.13- ASCII Even ...
    • Cincinnati 2100 Configuration

      CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (phone camera) original settings before making modifications! Baud ...
    • Yasnac I80 Configuration Document

      CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! Set the ...
    • Fadal Configuration Document

      CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! CD,8 ...