Fadal configuration document

Fadal configuration document


CNC Configuration Sheet

Fadal


CNC Parameters:

You will need to verify all parameters listed below that correspond to your CNC control.  These parameters may not match your particular machine‚Äôs control.  Document (Phone camera) original settings before making modifications!


CD,8 changes Baud Rate to 9600.


FactoryWiz DNC Settings:

Basic Communication

1.01- Port Type: Standard

1.11- Baud: 9600

1.12- Data Bits: 7

1.13- ASCII Even

1.14- Stop Bits: 1

1.15- Handshake: XON/XOFF


Sending Options

2.11- Leader: %<10>

2.12- Trailer: %

2.23- Skip lines that contain: %

2.31- Automatic timeout: 7


Receiving Options

3.11- Program identifier 1: O

3.12- Program Identifier 2: 

3.21- Receive timeout: 3

3.31- Ignore data before first end-of-block: True

3.32- Ignore data after last end-of-block: True

3.35- Ignore Fadal checksum: True


Remote Commands

4.02- Request for file command: GET-

4.03- Request for file command (drip feed): DNC-

4:11- Request to save command: PUT-


Additional Notes:

Changing default baud rate parameters:

To change the default baud rate parameter, type in SETP.

This will bring up the default parameters.

Cursor to the Baud rate section.

Select the default baud rate you would like when machine powers up.  An * will show the default setting.


Outputting CNC Programs:

PU,2 will output the active program.


Other Output options for CNC Programs:

** PU,0 will output the active program and tooling data.

PU,1 will output the tool data only.

PU,3 will output all programs in memory.

PU,4 will output parameters and backlash.


** Do not use PU,0 when saving programs and then sending program to different Fadal controls.  This will cause you to redo all tool offset settings.

Inputting CNC Programs:

TA,1 will load the program from the RS232 port into active memory.


Other Commands:

PR brings up the program menu. (create, delete, select, directory)
PR,xxxx brings up program xxxx. (for example, PR,1234 opens program 1234)
PA brings up the page editor with the active program.




Wiring Diagram:

Pinout includes RTS/CTS Handshaking


DB-9 com port

Wire color

DB-25 CNC

Jumper?


(Disconnected)

Shield

1



2 (Receive Data)

Green

2 (Transmit Data)



3 (Transmit Data)

Red

3 (Receive Data)



5 (Signal Ground)

Black

7 (Signal Ground)



7 (RTS)

Brown

5 (CTS)



8 (CTS)

Blue

4 (RTS)





6 (DSR)

8 (DCD)

20 (DTR)

JUMPER







    • Related Articles

    • Yasnac I80 configuration document

      CNC Configuration Sheet Yasnac I80 CNC Parameters: You will need to verify all parameters listed below that correspond to your CNC control.  These parameters may not match your particular machine’s control.  Document (Phone camera) original settings ...
    • Milltronics configuration document

      CNC Configuration Sheet Milltronics CNC Parameters: You will need to verify all parameters listed below that correspond to your CNC control.  These parameters may not match your particular machine’s control.  Document (Phone camera) original settings ...
    • Cincinnati 2100 configuration document

      CNC Configuration Sheet Cincinnati 2100 CNC Parameters: You will need to verify all parameters listed below that correspond to your CNC control.  These parameters may not match your particular machine’s control. Document (Phone camera) original ...
    • Yasnac MX1-LX2 configuration document

      CNC Configuration Sheet Yasnac MX1/LX1 CNC Parameters: You will need to verify all parameters listed below that correspond to your CNC control.  These parameters may not match your particular machine’s control.  Document (Phone camera) original ...
    • Yasnac MX3-LX3 configuration document

      CNC Configuration Sheet Yasnac MX3/LX3 CNC Parameters: You will need to verify all parameters listed below that correspond to your CNC control.  These parameters may not match your particular machine’s control.  Document (Phone camera) original ...