Step-by-Step Guide to Configuring Milltronics CNC

Milltronics Configuration

CNC Parameters

You will need to verify all parameters listed below that correspond to your CNC control.  These parameters may not match your particular machine’s control.  Document (Phone camera) original settings before making modifications!

Parameters can be found by:


From the MAIN MENU, press F7 UTIL, F8 PARAMS, F9 CTRL   or, From the MAIN MENU, press F7 PARAMS, F9 CTRL

Use the arrow keys to get down the list to change/verify the parameters. (use the F3 key to toggle between the options.)

FactoryWiz DNC Settings

Basic Communication


1.01- Port Type: Standard

1.11- Baud: 9600

1.12- Data Bits: 7

1.13- ASCII Even

1.14- Stop Bits: 2

1.15- Handshake: XON/XOFF

1.21- End of block (EOB) CRLF

 

Sending Options

2.11- Leader: %<13><10>

2.12- Trailer: %

2.23- Skip lines that contain: %

2.31- Automatic timeout: 7

 

Receiving Options

3.11- Program identifier 1: O

3.12- Program Identifier 2:

3.21- Receive timeout: 3

3.31- Ignore data before first end-of-block: True

3.32- Ignore data after last end-of-block: True

 

Remote Commands

4.02- Request for file command: GET-

4.03- Request for file command (drip feed): DNC-

4:11- Request to save command: PUT-

 

Outputting CNC Programs:

1). Press ESC until main menu appears.

2). Press F10 (Utilities).

3). Press F4 (RS232)

4). Press F5 (Send).

5). Press F1 (Text).

6). Press F7 (Menu).

7). Cursor to program for sending, and press F2 (Set).

8). Press START.

9). Press BEGIN.

 

Inputting CNC Programs:

1). Press ESC until main menu appears.

2). Press F10 (Utilities).

3). Press F4 (RS232).

4). Press F6 (Recv).

5). Press F1 (Text).

6). Type in PGM # and press ENTER.

 

 

Wiring Diagram: DB9 at hub, DB25 at machine

Pinout includes RTS/CTS Handshaking

DB-9 com port

Wire color

DB-25 CNC

Jumper?

 

(Disconnected)

Shield

1

 

 

2 (Receive Data)

Green

2 (Transmit Data)

 

 

3 (Transmit Data)

Red

3 (Receive Data)

 

 

5 (Signal Ground)

Black

7 (Signal Ground)

 

 

7 (RTS)

Brown

5 (CTS)

 

 

8 (CTS)

Blue

4 (RTS)

 

 

 

 

6 (DSR)

8 (DCD)

20 (DTR)

JUMPER

 

Wiring Diagram: DB9 at hub, DB9 at machine

Pinout includes RTS/CTS Handshaking

DB-9 com port

Wire color

DB-9 CNC

Jumper?

 

(Disconnected)

Shield

1

 

 

2 (Receive Data)

Green

3 (Transmit Data)

 

 

3 (Transmit Data)

Red

2 (Receive Data)

 

 

5 (Signal Ground)

Black

5 (Signal Ground)

 

 

7 (RTS)

Brown

8 (CTS)

 

 

8 (CTS)

Blue

7 (RTS)

 

 

 

 

6 (DSR)

1 (DCD)

4 (DTR)

JUMPER

 

 



    • Related Articles

    • Haas Configuration

      CNC Parameters Newer Haas Press SETNG to bring up the machine settings. Press right arrow until you get to I/O tab. Press WRITE/ENTER button (lower right corner of panel). Use left and right arrow to toggle between choices for each setting. Press ...
    • Brother C00 FTP Configuration

      CNC Configuration Sheet for FTP – Brother C00 You will need to verify all parameters listed below that correspond to your CNC control. Document (Phone camera) original settings before making modifications! CNC Parameters: Press EDIT button. Press ...
    • Cincinnati 2100 Configuration

      CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (phone camera) original settings before making modifications! Baud ...
    • Yasnac I80 Configuration Document

      CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! Set the ...
    • Fanuc 6MB Configuration Document

      CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF Input Device 1=1 Input Device 2=1 Param screen: 0311 = 00001001 0340 = 2 0341 = 2 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- ...