A Complete Guide To Integrating Okuma OSP100/200/300

Okuma P100, P200, P300 Serial Configuration

 

Okuma OSP100, OSP200, and OSP300

CNC Parameters

You will need to verify all parameters listed below that correspond to your CNC control.  These parameters may not match your particular machine’s control. Document (phone camera) original settings before making modifications!

Changing CNC Parameters

System (Param) screen:

Choose Parameters.

Page down until RS232 parameters appear for CN0.

Baud rate: Match FactoryWiz setting.
RS232C character: 8 bit  (cannot change, but you still set to 7 data bits in FactoryWiz)
RS232C parity bit: NON
RS232C stop bit: 2
Ready waiting time: 10 sec
Flow control: DC CODE
Delay timer until RS switches OFF: 0 msec
Designates the amount of RS OFF time: 0 msec
DC2/DC4 at punch: DOES NOT
DC when read/verify finished: DOES NOT

 

FactoryWiz DNC Settings

Basic Communication

1.01- Port Type: Standard

1.11- Baud: 4800

1.12- Data Bits: 7

1.13- ASCII Even

1.14- Stop Bits: 2

1.15- Handshake: XON/XOFF

 

Sending Options

2.11- Leader:

2.12- Trailer: %<0>

2.27- Force upper case: True

2.31- Automatic timeout: 7

 

Receiving Options

3.11- Program identifier 1: $

3.12- Program Identifier 2:

3.21- Receive timeout: 3

3.31- Ignore data before first end-of-block: False

3.32- Ignore data after last end-of-block: True

3.41- Mask characters: <0><18><20>

 

Remote Commands

4.02- Request for file command: GET-

4.03- Request for file command (drip feed): DNC-

4:11- Request to save command: PUT-


 

Additional Notes

Outputting CNC Programs

Press Edit/Aux.

Press right screen button until RS232 appears.

Press RS232.

Press Output.

Cursor to program you want sent, press OK.

 

Inputting CNC Programs

Press Edit/Aux.

Press right screen button until RS232 appears.

Press RS232.

Press Input.

Press OK.  Program will load with correct name if formatted correctly, otherwise it will load in as A.min


Wiring Diagram

Pinout includes RTS/CTS Handshaking

DB-9 com port

Wire color

DB-25 CNC

Jumper?

 

(Disconnected)

Shield

1

 

 

2 (Receive Data)

Green

2 (Transmit Data)

 

 

3 (Transmit Data)

Red

3 (Receive Data)

 

 

5 (Signal Ground)

Black

7 (Signal Ground)

 

 

7 (RTS)

Brown

5 (CTS)

 

 

8 (CTS)

Blue

4 (RTS)

 

 

 

 

6 (DSR)

8 (DCD)

20 (DTR)

JUMPER

 

 




    • Related Articles

    • Okuma P100 P200 P300 UNC Configuration

      Okuma Configuration On the Okuma, pressing Control plus Reset (looks like /// on the key) should bring up the start menu for Windows. In the start menu you want to run, then enter "compmgmt.msc" and click ok. There should be a local users and groups ...
    • Siemens 840D Serial Configuration

      CNC Parameters You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match your particular machine’s control. Document (Phone camera) original settings before making modifications! Changing ...
    • Moxa Configuration-Wizard (Wired)

      NPort 51xx Moxa Configuration NPort Windows Driver Manager (WHQL certified) NPort Search Utility Download current Moxa driver and firmware for your device (firmware may be out of date depending on supplier’s shelf life of product). Accessing the GUI ...
    • Fanuc 6MA Configuration Document

      CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF Input Device 1=0 Input Device 2=1 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 7 1.13- ASCII Even 1.14- Stop Bits: 1 ...
    • Fanuc 6TA Configuration Document

      CNC Parameters Setting (HANDY) screen: Punch code- 1=ISO TV CHECK=0 OFF Input Device 1=0 Input Device 2=1 FactoryWiz DNC Settings Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 7 1.13- ASCII Even 1.14- Stop Bits: 1 ...